shape parameters造句
例句與造句
- steel strands shape parameters of skew prestress box girder
斜交預應力箱梁鋼絞線形狀特性及其影響 - research on shape parameter of generalized nonlinear strength criterion
廣義非線性強度理論形狀參數研究 - shape parameter of boundary layer
邊界層的形狀參數 - interval estimator of shape parameter of three-parameter weibull distribution based on type-censored sample
分布定數截尾下形狀參數的區間估計 - nurbs curve equation contains two shape parameters, i . e . control convex and the weight factor
nurbs曲線方程包含了兩個形狀因子：控制頂點和相應控制頂點的權因子。 - It's difficult to find shape parameters in a sentence. 用shape parameters造句挺難的
- the estimation of the constant stress accelerated life tests with nonconstant shape parameter under weibull distribution
分布場合具有非常數形狀參數恒加試驗的參數估計 - the number of guiding channel is determined by the shape parameter b = b / a, whose cr itical value is 0.5389
形狀參數=ba的大小決定了磁導引通道的數目，其關鍵值為0.5389。 - by changing the value of the shape parameter, we can adjust the approaching degree of the curves to their control polygon
通過改變局部形狀參數的取值，可以調整曲線接近其控制多邊形的程度。 - in this paper a novel framework is presented for 2-d shape interpolation using the intrinsic shape parameters of a piecewise linear curve based on skeleton
本文基于骨架概念，根據多邊形內在量插值思想給出一個新穎的二維形狀插值算法框架。 - by changing the value of the shape parameter, we can adjust the approaching degree of the curves to their control polygon and manipulate the degree n bezier curves from both sides
通過改變形狀參數的取值，可以調整生成曲線從n次bzier曲線的兩側逼近n次bzier曲線。 - for instance, the development of the boundary-layer shape parameter can be prescribed on the upper surface to allow for maximum lift or extended runs of laminar flow, depending on the design requirements
比如開發了邊界層的形狀參數,可以指定允許的最高表面上取消或延期舉辦層流、視乎設計要求 - in the third chapter, we present a class of c2-continuous spline curves of degree 4 with some shape parameter . the segmented curves are all shape preserving to given polygon
第三章提出一類c~-連續的帶有形狀參數的四次樣條曲線，曲線上的所有曲線段的控制頂點由給定多邊形的頂點直接計算產生。 - based on the above work, the author analyzed the stress in an infinite plate with oval hole which is commonly used in structures and figured curves of stress concentration to hole's shape parameters
應用由該方法編制的程序?qū)こ躺铣Ｓ玫难鼒A孔口問題進行了應力分析，給出應力集中系數與孔口參數相關曲線。 - instead of the shape parameter a in c-b-splines, cosa, that is ck here, is used for the c-b-splines, and the definition interval of ck is extended to [-1, ) for the construction of catmull-clark subdivision surfaces
而且，用它作為catmull-clark細分的前置處理，效果良好。2)針對c-b樣條細分曲面形狀的調節范圍有限。 - (6 ) in the process of measurment, when measure the shape parameter, can calculate the max local-curvature, and analysis the angle from the edge-point to coordinate system to find the beginning point and stopping point of measure
(6)在參數測量中，通過分析肉牛形體特征，通過局部最大曲率以及考察點相對坐標夾角變化能夠較為準確的檢測測量點。
更多例句： 下一頁